USB Yaesu CAT Programming Cable FTDI FT231XS RS232 DB9 Serial Converter Cable for Yaesu FT-450 FT-950 FT-1000MP FT-2000 FT-9000 ST-9F Programming Cable
Connector A: USB 2.0 A Male
Connector B: DB9 Female
Chipset: FTDI FT231XS
CE,ROhs Compliance
Length:1.8m
Material : PVC Jacket, Bare Copper Wires
OD:3.5MM
System Support: Win7/8/10/11/xp/android/mac os/linux/vista
Application:
ST-49F
FT-450
FT-450AT
FT-450D
FT-950
FT-991A
FT-1000MP
FT-2000
FT-2000D
FTDX-1200
FTDX-3000
FTDX-5000
FTDX-9000
FTDI Driver Download : https://ftdichip.com/drivers/vcp-drivers/
Installation Guides : https://ftdichip.com/document/installation-guides/
About FTDI FT231
FT231X – Full Speed USB to Full Handshake UART
Key Hardware Features
This USB2.0 Full Speed IC offers a compact bridge to full handshake UART interfaces. The device is a UART, capable of operating up to 3MBaud, with low power consumption (8mA). The FT231X includes the complete FT-X series feature set and enables USB to be added into a system design quickly and easily over a UART interface.
Single chip USB to asynchronous serial data transfer interface.
Entire USB protocol handled on the chip. No USB specific firmware programming required.
Fully integrated 2048 byte EEPROM for storing device descriptors and CBUS I/O configuration.
Fully integrated clock generation with no external crystal required plus optional clock output selection enabling a glue-less interface to external MCU or FPGA.
Data transfer rates from 300 baud to 3 Mbaud.
512 byte receive buffer and 512 byte transmit buffer utilizing buffer smoothing technology to allow for high data throughput.
FTDI’s royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the requirement for USB driver development in most cases.
Configurable CBUS I/O pins.
Transmit and receive LED drive signals.
UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity
Synchronous and asynchronous bit bang interface options with RD# and WR# strobes.
Battery Charger Detection. May be used by mobile devices to detect the presence of a charger on the USB port to enable higher current / faster charging of batteries.
Device supplied pre-programmed with unique USB serial number.
Supports bus powered, self powered and high-power bus powered USB configurations.
Integrated +3.3V level converter for USB I/O.
True 3.3V CMOS drive output and TTL input.
(operates down to 1V8 with external pull ups and is also 5V tolerant)
Configurable I/O pin output drive strength.
Integrated power-on-reset circuit.
UART signal inversion option.
Internal 3.3V/1.8V LDO regulators
Low operating current of 8mA (typical) and USB suspend current of 125uA (typical) current.
Low USB bandwidth consumption.
UHCI/OHCI/EHCI host controller compatible.
USB 2.0 Full Speed compatible.
Extended operating temperature range: -40°C to 85°C
Available in compact Pb-free 20 Pin SSOP and QFN packages (both RoHS compliant).
Typical Applications
Dedicated Charger Port (DCP) detection enabling battery charging at higher current for faster charge times.
USB Bar Code Readers
USB Wireless Modems
USB Hardware Modems
USB Digital Camera Interface
Set Top Box PC – USB interface
USB FLASH Card Reader and Writers
USB MP3 Player Interface
USB Industrial Control
USB Instrumentation
USB Smart Card Readers
PDA to USB data transfer
USB Audio and Low Bandwidth Video data transfer
Interfacing MCU/PLD/FPGA based designs to USB
Cellular and Cordless Phone USB data transfer cables and interfaces
Upgrading Legacy Peripherals to USB
USB to RS232/RS422/RS485 Converters
